玖玖玖视频-亚洲精品1卡2卡3卡-操欧美美女-真实国产乱子伦对白视频不卡-国产乱在线-大胸美女被吃奶爽死视频-久久亚洲美女精品国产精品-天堂在线www天堂在线-久久在精品线影院精品国产-国产又粗又长又大-欧美三级一区二区-超碰在线亚洲-天天cao在线-国产偷倩视频-亚洲啪

我是新人小白,請大神幫忙我一下啊,看看我哪里寫錯了呀,
三菱ST中DDRVA執行后,DZRN無法回歸原點的問題,單獨回原點正常,執行DDRVA移動后,再執行DZRN就無動作 詳細請幫忙看看下面的程序

(*校準螺距*)
Current_Distance := Pulse_Current_Distance / ONE_Pulse_Feed;
IF Calibration THEN(*如果校準按鈕被按下*)
    ONE_Pulse_Feed := Calibration_Distance / Pitch_Setting * K100;(*計算1mm所用脈沖值*)
    DDRVA ( Calibration,Calibration_Distance,Feeding_Distance,Pulse_Output,Y001);
    Direction_Output :=TRUE;(*正轉方向啟動*)
    IF M8029=TRUE THEN
        Direction_Output := FALSE;
        Calibration := FALSE;(*否則RST校準按鈕*)    
    END_IF;
END_IF;

(*回原點*)
IF    NOT Backward_Limit AND NOT Enclosure_Not_Closed AND NOT Backward_Limit THEN
    DZRN (Back_Servo_Origin,K2000,K1000,Servo_Origin,Pulse_Output);
    IF Back_Servo_Origin THEN
    OUT_T(Scintillation=1,TC2,K10);
    OUT_T(Servo_Origin_Lamp =TRUE,TC1,K10);
        IF TC2 =TRUE THEN
            Servo_Origin_Lamp :=TRUE;
            IF TC1 =TRUE THEN
                Scintillation :=0;
            END_IF;
        ELSIF TC2 =FALSE THEN
            Servo_Origin_Lamp :=FALSE;
            Scintillation :=1;
        END_IF;
    END_IF;
END_IF;
IF Back_Servo_Origin THEN    
    IF Pulse_Current_Distance =K0  THEN
        Back_Servo_Origin :=FALSE;
        Servo_Origin_Lamp :=TRUE;
    END_IF;
ELSIF Pulse_Current_Distance <>K0 THEN
    Servo_Origin_Lamp :=FALSE;
END_IF;


最后在論壇的好心大哥幫助下,完美解決,提供修改的程序,幫忙大家避坑!!

IF Calibration THEN
    IF LDF(TRUE ,OUT_Puls_Monitor) THEN
        M340:=1;
    END_IF;
    OUT_T(M340=1,TC3,K100);
    IF TC3=1 THEN
        Calibration := FALSE;
        M340:=0;
    END_IF;
END_IF;

M8029貌似一般都用上升沿